{"id":5412,"date":"2024-09-05T02:11:39","date_gmt":"2024-09-05T02:11:39","guid":{"rendered":"http:\/\/121.199.166.88\/?post_type=resources&p=5412"},"modified":"2024-09-05T17:14:39","modified_gmt":"2024-09-05T17:14:39","slug":"thermocouple-calibration-for-the-autochem-thermostar-interface","status":"publish","type":"resources","link":"https:\/\/micromeritics.com.cn\/en\/resources\/thermocouple-calibration-for-the-autochem-thermostar-interface\/","title":{"rendered":"Thermocouple Calibration for the AutoChem \u2013 Thermostar Interface"},"content":{"rendered":"\n

Micromeritics\u2019 AutoChem series of instruments is equipped with both digital and analog I\/O (inputs\/outputs), which may be used to control a Pfeiffer Vacuum Thermostar mass spectrometer via a single interface (Micromeritics\u2019 part number 291\/60811\/00<\/em>). This cable has been specifically designed to provide the hardware interface between the two instruments. The single-connector cable end is attached to the mass spectrometer*. The double-connector cable end (consisting of small and large connectors) is connected to the AutoChem. The small connector is attached to the Analog I\/O and the large connector attached to the Digital I\/O.<\/p>\n\n\n\n

The Quadstar software package from Pfeiffer Vacuum consists of several applications which are primarily used for the configuration of the Thermostar mass spectrometer and collection of mass spectrometer data. Pfeiffer Vacuum has also developed the TG-MS software macros for use with the Quadstar software. This suite of macros used with the Quadstar software and Micromeritics\u2019 cable interface allows AutoChem users full control of their thermostar mass spectrometer.<\/p>\n\n\n\n

Several parameters must be established to utilize the Quadstar software to the fullest. A simple thermocouple calibration is the most significant.<\/p>\n\n\n\n

    \n
  1. Launch the Quadstar Parset<\/em> program; use one of the following methods:<\/li>\n<\/ol>\n\n\n\n
      \n
    • Select Start<\/strong> > Programs<\/strong> > Quadstar<\/strong> > Parset<\/strong><\/li>\n\n\n\n
    • Double-click the Quadstar icon on the Windows desktop, then double-click the Parset<\/strong> icon.<\/li>\n<\/ul>\n\n\n\n

      2. Select Config<\/strong> > AI Characteristic Curve<\/strong>; the AI Characteristic Curve dialog is displayed. Use this dialog to define parameters for the Detector and Thermocouple signals.<\/p>\n\n\n\n

      3. Configure the Detector signal as follows:
      a. Click the up\/down arrow in the AI-Channel<\/strong> field until 0<\/strong> is displayed.
      b. Enter Detector<\/strong> in the AI-Type<\/strong> field.
      c. Enter mV<\/strong> in the Unit<\/strong> field.
      d. Click Formula<\/strong>; enter X<\/strong> as the formula, -5000<\/strong> in the Minimal X<\/strong> field and 5000<\/strong> in the Maximal<\/strong> field.
      *The cover must be removed from the Thermostar to make this connection; refer to the Thermostar manual for instructions on removing the cover.<\/p>\n\n\n\n

      \"\"<\/figure>\n\n\n\n
        \n
      1. Configure the Thermocouple signal:
        a. Click the up\/down arrow in the AI-Channel<\/strong> field until 1<\/strong> is displayed. All parameters defined for 0<\/strong> (Detector) are saved automatically when 1<\/strong> displays.
        b. Enter T inC<\/strong> in the AI-Type<\/strong> field. Be sure to space between T<\/strong> and inC<\/strong>; otherwise, the AutoChem software cannot properly identify the temperature signals.
        c. Enter C<\/strong> in the Unit<\/strong> field.
        d. Click Formula<\/strong>; enter X<\/strong> as the formula, -5000<\/strong> in the Minimal X<\/strong> field and 5000<\/strong> in the Maximal<\/strong> field.<\/li>\n<\/ol>\n\n\n\n
        \"\"<\/figure>\n\n\n\n

        5. Click OK <\/strong>to close the AI-Characteristic Curve dialog.<\/p>\n\n\n\n

        With these parameters set, you can now develop a thermocouple calibration.<\/p>\n\n\n\n

          \n
        1. Select Measure<\/strong> > MID<\/strong> from the main menu of the Parset<\/strong> application; the MID Parameters dialog is displayed. This dialog is used to specify the signals to be recorded by the Thermostar.<\/li>\n\n\n\n
        2. Choose parameters for the calibration:
          a. Right-click in the State<\/strong> > CH-0<\/strong> field; select Enable<\/strong> from the pop-up menu.
          b. Right-click in the Det. Type<\/strong> > CH-0<\/strong> field; select A1<\/strong> > T inC<\/strong>.<\/li>\n<\/ol>\n\n\n\n
          \"\"<\/figure>\n\n\n\n
            \n
          1. Specify mass signals (required for the Thermostar to collect data); an example is given here. Save this file as mstcal.mip<\/strong>. Refer to your Thermostar instruction manual if assistance is needed for this
            step.<\/li>\n<\/ol>\n\n\n\n
            \"\"<\/figure>\n\n\n\n
              \n
            1. Create a sample file (AutoChem software) for the thermocouple calibration; in this example we use mstcal01.smp<\/strong>. On the Analysis Conditions dialog, define the parameters as follows:<\/li>\n<\/ol>\n\n\n\n
              \"\"<\/figure>\n\n\n\n

              The synopsis in your sample file should look similar to the following:<\/p>\n\n\n\n

              \"\"<\/figure>\n\n\n\n
                \n
              1. Click the TG-MS V5<\/strong> icon (on your desktop) to start the program.<\/li>\n<\/ol>\n\n\n\n
                \"\"<\/figure>\n\n\n\n

                Untriggered Runs<\/strong> are for manual operation and TG-Triggered Runs<\/strong> are for operation using the AutoChem.<\/p>\n\n\n\n

                  \n
                1. Click RUN TREND SCAN<\/strong> to display the Trend Scan Select (triggered) dialog.
                  a. Click File Manager<\/strong> (upper one) and choose mstcal.mip<\/strong> for the method to run.
                  b. Click File Manager<\/strong> (lower one); enter a file name for the calibration data, this example uses mt_tcal.mdc<\/strong>.
                  c. Click START ON TRIGGER<\/strong> to close the dialog; the Thermostar is now being controlled by the AutoChem software.<\/li>\n<\/ol>\n\n\n\n
                  \"\"<\/figure>\n\n\n\n
                    \n
                  1. From the AutoChem software, select Unit 1<\/strong> > Start Analysis<\/strong>; choose mstcal01.smp<\/strong> as the sample file.<\/li>\n\n\n\n
                  2. Click Next<\/strong> to start the analysis.
                    <\/li>\n<\/ol>\n\n\n\n

                    Data will be recorded by both the AutoChem and the Thermostar. Example data are shown in Figures 1 and 2<\/strong>.<\/p>\n\n\n\n

                    \"Typical
                    Figure 1. Typical mV versus time collected using the Thermostar.<\/figcaption><\/figure>\n\n\n\n
                    \"Regression
                    Figure 2. Regression results from AutoChem temperature versus AI-1 mV data collected using the Thermostar.<\/figcaption><\/figure>\n\n\n\n

                    The Thermostar signal versus AutoChem temperature plot (Figure 2) yields a linear relationship. To update the AI-1 Characteristic<\/strong> curve:<\/p>\n\n\n\n

                      \n
                    1. Select Config<\/strong> > AI Characteristic Curve<\/strong> from the main menu of the Parset<\/strong> application.<\/li>\n\n\n\n
                    2. Click the up\/down arrow in the AI-Channel<\/strong> field until 1<\/strong> is displayed.<\/li>\n\n\n\n
                    3. Enter the value displayed for the temperature.<\/li>\n<\/ol>\n\n\n\n
                      \"\"<\/figure>\n\n\n\n

                      Future analyses will now contain a temperature signal in addition to any mass signals that are recorded.<\/p>\n","protected":false},"excerpt":{"rendered":"

                      Micromeritics\u2019 AutoChem series of instruments is equipped with both digital and analog I\/O (inputs\/outputs), which may be used to control a Pfeiffer Vacuum Thermostar mass spectrometer via a single interface (Micromeritics\u2019 part number 291\/60811\/00). This cable has been specifically designed to provide the hardware interface between the two instruments. The single-connector cable end is attached […]<\/p>\n","protected":false},"featured_media":0,"parent":0,"template":"","meta":{"_acf_changed":false},"methods":[25],"resource_type":[8],"class_list":["post-5412","resources","type-resources","status-publish","hentry","methods-chemisorption","resource_type-application-notes"],"acf":[],"_links":{"self":[{"href":"https:\/\/micromeritics.com.cn\/en\/wp-json\/wp\/v2\/resources\/5412","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/micromeritics.com.cn\/en\/wp-json\/wp\/v2\/resources"}],"about":[{"href":"https:\/\/micromeritics.com.cn\/en\/wp-json\/wp\/v2\/types\/resources"}],"wp:attachment":[{"href":"https:\/\/micromeritics.com.cn\/en\/wp-json\/wp\/v2\/media?parent=5412"}],"wp:term":[{"taxonomy":"methods","embeddable":true,"href":"https:\/\/micromeritics.com.cn\/en\/wp-json\/wp\/v2\/methods?post=5412"},{"taxonomy":"resource_type","embeddable":true,"href":"https:\/\/micromeritics.com.cn\/en\/wp-json\/wp\/v2\/resource_type?post=5412"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}