{"id":4804,"date":"2024-08-05T19:09:46","date_gmt":"2024-08-05T19:09:46","guid":{"rendered":"http:\/\/121.199.166.88\/?post_type=resources&p=4804"},"modified":"2024-09-06T19:02:43","modified_gmt":"2024-09-06T19:02:43","slug":"breakthrough-analysis-on-the-autochem","status":"publish","type":"resources","link":"https:\/\/micromeritics.com.cn\/en\/resources\/breakthrough-analysis-on-the-autochem\/","title":{"rendered":"Breakthrough Analysis on the AutoChem"},"content":{"rendered":"\n

Introduction<\/strong><\/h3>\n\n\n\n

The AutoChem is a flow-through system that allows for the characterization of catalysts for surface activity. The AutoChem can also function as a basic single component breakthrough unit allowing for carrier, preparation, and analysis gas flows. This document will describe how to perform a breakthrough analysis using the AutoChem alongside a mass spectrometer.<\/p>\n\n\n\n

Experimental<\/strong><\/h3>\n\n\n\n

Zeolite 13X was used as a standard reference material for carbon dioxide breakthrough analysis. Figure 1<\/strong> below shows the instrument schematic that was used for the breakthrough analysis. Prior to analysis, the sample was heated to 200 \u00b0C at 10 \u00b0C\/min under nitrogen gas flow at a rate of 20 sccm overnight. The sample temperature was then cooled to the analysis temperature of 30\u00b0C. Next the mass spectrometer was turned on while continuing to flow nitrogen gas through the carrier line.<\/p>\n\n\n

\n
\"\"
Figure 1<\/strong>. AutoChem CO2<\/sub> breakthrough analysis.<\/figcaption><\/figure>\n<\/div>\n\n\n

Before breakthrough measurements, the deadtime of the system was calculated. The deadtime
is the time that it takes for the gas to flow through the system and reach the mass spectrometer.
The deadtime was determined by flowing nitrogen through the carrier gas line (20 sccm) and
helium through the loop gas line (20 sccm). The flows were alternated and the time was recorded
between when the valve was turned on and a difference in mass signal was detected by the mass
spectrometer. After several measurements, the deadtime was determined to be 14.5 seconds for a
flowrate of 20 sccm.<\/p>\n\n\n\n

Following the determination of the deadtime, the flow of gas through the loop was switched from
helium to CO2<\/sub> (20 sccm). After establishing the flow for several minutes, breakthrough began by
switching on the flow of CO2<\/sub> from the loop. Following breakthrough measurements, the sample
furnace was heated to 200\u00b0C for several hours to ensure the complete desorption of carbon
dioxide from zeolite 13X.<\/p>\n\n\n\n

Results<\/strong><\/h3>\n\n\n\n

The results of the breakthrough experiment are shown below. Zeolite 13X showed strong adsorption
for CO2 at ambient conditions reaching a capacity of 4.53 mmol\/g. Additionally, the breakthrough
curve is steep signifying that there are little to no mass transfer limitations in the system.<\/p>\n\n\n

\n
\"\"
Figure 2<\/strong>. CO2<\/sub> breakthrough adsorption in zeolite 13X.<\/figcaption><\/figure>\n<\/div>\n\n\n

Conclusions<\/strong><\/h3>\n\n\n\n

The AutoChem is a capable unit for performing simple single component breakthrough analysis. This was confirmed via analysis of zeolite 13X, achieving a CO2<\/sub> adsorption capacity of 4.53 mmol\/g at 30\u00b0C and a flowrate of 20 sccm.<\/p>\n","protected":false},"excerpt":{"rendered":"

Introduction The AutoChem is a flow-through system that allows for the characterization of catalysts for surface activity. The AutoChem can also function as a basic single component breakthrough unit allowing for carrier, preparation, and analysis gas flows. This document will describe how to perform a breakthrough analysis using the AutoChem alongside a mass spectrometer. Experimental […]<\/p>\n","protected":false},"featured_media":4824,"parent":0,"template":"","meta":{"_acf_changed":false},"methods":[25,207],"resource_type":[8],"class_list":["post-4804","resources","type-resources","status-publish","has-post-thumbnail","hentry","methods-chemisorption","methods-gas-adsorption","resource_type-application-notes"],"acf":[],"_links":{"self":[{"href":"https:\/\/micromeritics.com.cn\/en\/wp-json\/wp\/v2\/resources\/4804","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/micromeritics.com.cn\/en\/wp-json\/wp\/v2\/resources"}],"about":[{"href":"https:\/\/micromeritics.com.cn\/en\/wp-json\/wp\/v2\/types\/resources"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/micromeritics.com.cn\/en\/wp-json\/wp\/v2\/media\/4824"}],"wp:attachment":[{"href":"https:\/\/micromeritics.com.cn\/en\/wp-json\/wp\/v2\/media?parent=4804"}],"wp:term":[{"taxonomy":"methods","embeddable":true,"href":"https:\/\/micromeritics.com.cn\/en\/wp-json\/wp\/v2\/methods?post=4804"},{"taxonomy":"resource_type","embeddable":true,"href":"https:\/\/micromeritics.com.cn\/en\/wp-json\/wp\/v2\/resource_type?post=4804"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}